– current  January 2012

1. SIZES – RAW BRUSHWOOD PANELS

2. SIZES – FACTORY PRE-FRAMED PANELS

3. SIZES – BRUSH ROLLTOP FINISHES

4. SIZES – BRUSH GATES

1. SIZES – RAW BRUSHWOOD PANELS

Prices on application – contact Hague Showell by email here.

THESE ARE STOCK SIZES –

OTHER SIZES CAN BE MADE TO ORDER IN PALLET QUANTITIES

 

RETAIL PRICES / panel,

Contact your local installer or ausbrush for pricing details

 AU$ including GST, ex Adelaide

Surcharge on part-pallet order quantities

AU$ incl GST

Cost of throwaway Pallet Bases

AU$ incl GST

Wire at ends of panels extend out 120mm to provide for in-line panel installation (to allow tensioning around posts).

Stock Panel Sizes

 Height  mm

 Width mm

Maximum Number of Raw Brush Panels per Pallet

Pallet Size

 48mm thickness

 58mm thickness

17001100201700×1100YN  No
17002200201030×2200YN contact us by email for current pricesYes
17002400161030×2200NY  Yes
2120 ‘Jumbo’ 2200101030×2200YN  Yes
1700 ‘Super Thick’2400161030×2200NY , 64mm Super Thick  Yes

What’s New !    for those jobs where additional privacy is required our new  2120mm high, raw brush panels    

ausbrush supplies raw, machine compressed, brushwood fencing panels to fencing contractors, DIY handymen and distributors Australia wide.  Brush panels are produced primarily in heights of 1700mm high or 2120mm high, in widths from 1200mm to 2400mm, in thickness of 48mm and 58mm.  Panel weights are around 37 to 46Kg for an 1100mm wide panel depending on height, moisture content of brush and panel thickness.  Our stock sizes shown in the table above can be purchased in either large or small quantities.  The cheapest way to buy is in standard pallet quantities from our Shopping Carts.  The offering provide standard panel sizes and pallet quantities either with or without brush roll tops.

2120mm high panels have recently been added to our product range, although the present standard of 1700mm is ideal for most fencing installations.  An overall fence height of 2200mm or more can also be achieved with 1700mm high panels, depending on base height and top finish etc and an overall fence height of 2350mm using the 2120mm high panels.  A boxed section timber base using decking boards and mid-span post stubs, can also be used to gain additional base and overall fence height – see this page for images and ideas for added height.

For low fences, the panels can be easily cut to lesser height on site, using a power saw and ripping blade and panels can be cut for width using pliers.

The size and thickness of brushwood panels needed will depend on the framing system and number of persons installing.  Generally for a one person install (eg using the “offset system”), a panel width of 1100mm is manageable (37 to 40kg), but for the longer panel sizes, two strong people are needed for ease of panel handling and installation.

ausbrush‘ProtaCoat’ which has preservative, anti-fungal, pest resistant and fire retardant properties, can be purchased in 3.6 litre containers and applied after fence installation to any of our panel sizes.

See here  for raw panel installation methods and materials and fittings required, including video and still images.

For further information please contact  Hague Showell at  ausbrush

Sizes & Products Current  June 2013

Note:   Sizes subject to change without notice.  Indicative pricing for freight of panels to various centres within Australia are included in Table C

2. SIZES – FACTORY PRE-FRAMED PANELS

THESE ARE NO LONGER SUPPLIED PRE-MADE

Information has been left up on this site for DIY info.. ie using our raw panels and local framing …

 

Maximum Number of Panels per Pallet

 RETAIL PRICES / panel,

 AUD$, including GST, ex Adelaide

Loading on part-pallet order quantities

AU$  incl GST

Cost of throwaway Pallet Bases

AU$ incl GST

Framed Panel Size

 Height  mm

 Width mm

 

Size of Pallet Base

Panel Thickness

PRE-FRAMED BRUSH PANELSFULLY FINISHED, POWDER-COATED, TWO IN-GROUND LEGS                            
   

extended pallet base 2410mmx1850mm

Uses 48mm thick raw brush panels

  
17601800up to 16 pre-framed modules per palletContact ausbrush for pricing details     
     
2400mm overall side length.  

 

  

Panels are assembled and ready to stand

     

 ausbrush NO LONGER supplies fully assembled, powder-coated steel channel framed, brush fencing panels incorporating legs, which are ready to install and simply requires digging holes, standing the panels, concreting the holes and they are done.    Typical uses for framed panels include, unit dividers, partitions, fencing, privacy fence screens, sloping site installations, service enclosures – such as rubbish, / trash, pool pump enclosures – patio and swimming pool fencing, golf course service yards, car park enclosures, windbreaks, tourist resort screening, screening of building extensions and service yards and temporary event screening.

See here  for pre-framed panel installation methods including video and still images.

Prices on application – contact Hague Showell by email here.

Note:  Indicative pricing for freight of panels to various centres within Australia are included in Table C

3. SIZES – BRUSHWOOD ROLL-TOP & POST-ROLL FINISHES

Prices can be obtained from Hague Showell at ausbrush direct.

 RETAIL PRICES / roll,

 AUD$, including GST, ex Adelaide

Shipping

Brush Roll Length (mm) –  other sizes to order

ROLL TOPS (ROLL CAPS)
1800 shipped on top of panel orders
   
2200Contact ausbrush for pricing details
   
   
END POST ROLLS
1700Contact ausbrush for pricing detailsshipped on top of panel orders
   
STANDARD POST ROLLS
1700Contact ausbrush for pricing detailsshipped on top of panel orders
   
   

Sizes & Products current at June 2013

ausbrush supplies brush roll-tops (‘rollcap’) and post rolls for use in fence finishing.  The rolls have wires incorporated which are long enough to provide securing on installation.  The wire ends are folded underneath the rolls for shipping purposes.  Roll-tops secure as a tensioned wire loop, while post rolls tie off to the panel ‘running’ wires on either side.

The Roll Tops are supplied in 1800mm and 2200mm lengths and can be blended during installation at the joins to form a seamless roll.  The length supplied is usually dictated by the size/format of the panels on which it is to be stacked for shipping.  Normally 1800mm long roll tops are shipped on top of panels up to 1800mm in width and 2200mm long roll tops with 2200mm wide panels.  On our standard Shopping Cart pallet quantities roll tops to suit are now shipped on top of the standard pallets of brushwood panels.

Brush Post Rolls are now made from roll top sections on site (two post rolls can be obtained from each 1800mm long roll top).   They are 1700mm long and in two varieties, standard post rolls, used for covering the face of mid posts on both sides of the fence and wider end-post rolls used to wrap around the end fence posts.  Contractors also use fencing panels sacrificially for post rolls.  Approximately 10 post rolls can be derived per metre of brush panel.

See here  for brush roll top installation methods including video and still images.

Prices on application – contact Hague Showell by email here

Indicative pricing for freight of panels to various centres within Australia are shown in Table C

4. SIZES – BRUSH GATES

Prices can be obtained from your local installer , or from Hague Showell at ausbrush direct.

 RETAIL PRICES / Gate,

 AUD$, including GST, ex Adelaide

Shipping

Brush Gate Sizes (mm) –  other sizes to order

PEDESTRIAN GATES

Heavy Duty Pedestrian Gate

 for use with conventionally framed fences using concrete or timber base (has all welded and powdercoated construction)

1800mm high x 900mm wide

and 1750mm highx 900mm wide

POA   incl.hinges, ‘D’ latch (non keyed), Striker & Handles.  Lokk Latch Pro key lockable latches are also available for use with these gates.

shipped on top of panel orders

   
DRIVEWAY GATES

Brush Driveway Gates for use with conventionally framed fences using concrete or timber base (has all welded and powdercoated construction), two leaves

  1750mm high x 1400mm wide

 1800mm high x 1400mm wide

POA  per pair, incl.hinges, ‘D’ latch (non keyed), Striker, Handles and Drop-boltsshipped on top of panel orders

Brush Driveway Gates for use with conventionally framed fences using concrete or timber base (has all welded and powdercoated construction), two leaves

 1750mm high x 1600mm wide

1800mm high x 1600mm wide,

POA   per pair, incl.hinges, ‘D’ latch (non keyed), Striker, Handles and Drop-boltsshipped on top of panel orders
   

ausbrush supplies standard sizes of heavy duty brushwood pedestrian and driveway gates for ‘post and rail’ framed brush fences and also makes other gate sizes to order.  The heavy duty gates have powder-coated steel finishes and are available either with powdercoated channel or brush roll top finish and can be supplied with either key lockable Latch Lokk Pro  or simple ‘D’ latches.

See here  for bush gate installation methods including video and still images.

NEW !    Now Available raw brush panels in heights of 2120mm where additional overall fence height and privacy is required.

Sizes and products current at June 2013

DIY, Retail, Wholesale/Trade and Volume Sales prices on application – contact Hague Showell by email here.

Sizes:    The sizes listed in these tables are subject to change without notice.   Freight from Adelaide terminal to various destinations is not included.  Indicative pricing for freight of panels to various centres within Australia are shown in Table C

Ausbrush Panels Pty Ltd,  Last Updated   June 2013