Sizes    - current  January 2012

1. SIZES - RAW BRUSHWOOD PANELS

2. SIZES - FACTORY PRE-FRAMED PANELS

3. SIZES - BRUSH ROLLTOP FINISHES

4. SIZES - BRUSH GATES

1. SIZES - RAW BRUSHWOOD PANELS

Prices on application - contact Hague Showell by email here.

What's New !    for those jobs where additional privacy is required our new  2120mm high, raw brush panels    

ausbrush supplies raw, machine compressed, brushwood fencing panels to fencing contractors, DIY handymen and distributors worldwide.  Brush panels are produced in many sizes, but primarily in heights of 1700mm high or 2120mm high, in widths from 1000mm to 2400mm, in thickness of 48mm and 58mm.  Panel weights are around 37 to 46Kg for an 1100mm wide panel depending on height, moisture content of brush and panel thickness.  Our stock sizes shown in the table above can be purchased in either large or small quantities.  Other sizes can be made to order in pallet quantities.

2120mm high panels have recently been added to our product range, although the present standard of 1700mm is ideal for most fencing installations.  An overall fence height of 2200mm or more can also be achieved with 1700mm high panels, depending on base height and top finish etc and an overall fence height of 2350mm using the 2120mm high panels.  A boxed section timber base using decking boards and mid-span post stubs, can also be used to gain additional base and overall fence height - see this page for images and ideas for added height.

For low fences, the panels can be easily cut to lesser height on site, using a power saw and ripping blade and panels can be cut for width using pliers.

The size and thickness of brushwood panels needed will depend on the framing system and number of persons installing.  Generally for a one person install (eg using the "offset system"), a panel width of 1100mm is manageable (37 to 40kg), but for panels wider than 1400mm and in pre-framed panels, two strong people are needed for ease of panel handling and installation.

We are the only Australian brushwood panel supplier to offer as an option, a specially coated brush panel which has preservative, anti-fungal, pest resistant and fire retardant properties.  Pre-treated panels in ausbrush 'ProtaCoat'  finish are available in 1700mm high x 1100mm wide x 48mm panel size.  ausbrush'ProtaCoat' can be purchased in 3.8 litre containers and applied after fence installation to any of our larger panel sizes.

See here  for raw panel installation methods and materials and fittings required, including video and still images.

Supply & Install Prices can be obtained from a  local installer , and factory direct DIY Materials Supply Prices from Hague Showell  ausbrush

Sizes & Products Current  September 2012

Note:   Sizes subject to change without notice.  Indicative pricing for freight of panels to various centres within Australia are included in Table C. 

2. SIZES - FACTORY PRE-FRAMED PANELS

Prices can be obtained from Hague Showell at ausbrush direct. 

 Sizes and products current September 2012

ausbrush supplies fully assembled, powder-coated steel channel framed, brush fencing panels incorporating legs, which are ready to install and simply requires digging holes, standing the panels, concreting the holes and they are done.    Typical uses for framed panels include, unit dividers, partitions, fencing, privacy fence screens, sloping site installations, service enclosures - such as rubbish, / trash, pool pump enclosures - patio and swimming pool fencing, golf course service yards, car park enclosures, windbreaks, tourist resort screening, screening of building extensions and service yards and temporary event screening.

See here  for pre-framed panel installation methods including video and still images.

Prices on application - contact Hague Showell by email here.

Note:  Indicative pricing for freight of panels to various centres within Australia are included in Table C. 

3. SIZES - BRUSHWOOD ROLL-TOP & POST-ROLL FINISHES

Prices can be obtained from Hague Showell at ausbrush direct.

Sizes & Products current at September 2012

ausbrush supplies brush roll-tops ('rollcap') and post rolls for use in fence finishing.  The rolls have wires incorporated which are long enough to provide securing on installation.  The wire ends are folded underneath the rolls for shipping purposes.  Roll-tops secure as a tensioned wire loop, while post rolls tie off to the panel 'running' wires on either side.

The Roll Tops are supplied in 1800mm and 2200mm lengths and can be blended during installation at the joins to form a seamless roll.  The length supplied is usually dictated by the size/format of the panels on which it is to be stacked for shipping.  Normally 1800mm long roll tops are shipped on top of panels up to 1800mm in width and 2200mm long roll tops with 2200mm wide panels.

Post Rolls are made 1700mm long and in two varieties, standard post rolls, used for covering the face of mid posts on both sides of the fence and wider end-post rolls used to wrap around the end fence posts.  Contractors also use fencing panels sacrificially for post rolls.  Approximately 10 post rolls can be derived per metre of brush panel.

See here  for brush roll installation methods including video and still images.

Prices on application - contact Hague Showell by email here

Indicative pricing for freight of panels to various centres within Australia are shown in Table C

4. SIZES - BRUSH GATES

Prices can be obtained from your local installer , or from Hague Showell at ausbrush direct.

ausbrush supplies standard sizes of modular brushwood pedestrian and driveway gates for both 'post and rail' framing system fences and also for the factory pre-framed modular systems and also makes other gate sizes to order.  The modular gates have powder-coated steel channel finishes.

See here  for bush gate installation methods including video and still images.

NEW !    Now Available raw brush panels in heights of 2120mm where additional overall fence height and privacy is required.

Sizes and products current at January 2012

DIY, Retail, Wholesale/Trade and Volume Sales prices on application - contact Hague Showell by email here.

Sizes:    The sizes listed in these tables are subject to change without notice.   Freight from Adelaide terminal to various destinations is not included.  Indicative pricing for freight of panels to various centres within Australia are shown in Table C

Copyright:  Ausbrush Panels Pty Ltd,  Last Updated   Jan 2012                                   back to top