|
ausbrush panels Reg T.M. N0: 1086159 Office: 23 Pangari Dv, Fairview Park, South Australia Factory/Warehouse: 38-46 Barndioota Rd Salisbury Plain, SA 5109 ph +61 8 8251 3309, fax +61 8 8289 3155, mobile 0418 841 889
Home Products Sizes Ordering Installers Photo Gallery Contact Us
|
![]() - Brushwood Gates |
Modular Brushwood Gates
Australian Registered Design No. 319331
Pedestrian gates are made in two standard sizes;
1) a 1730mm high x 900mm wide gate for use with the ausbrush pre-framed panel system
2) an 1800mm high x 900mm wide for general use with traditional brush fencing and conventional framing systems and for export markets.
Driveway gates pairs are also made in standard sizes:
1) 1730mm high x 1400mm wide each leaf and
2) 1800mm high x 1600mm wide each leaf.
The modular construction using powder-coated, galvanised steel channel sections together with long lasting Australian Melaleuca uncinata hardwood panels, provides a very rigid, strong yet lightweight gate which is both attractive and economical in cost. The gates are of universal installation design, shipping with universal hinges (fit left or right hand installs), latches, strikers, handles and fixing screws.
ausbrush can supply other sizes of modular gates to order, but cost more and do not offer the same economies of construction as the standard modular gate, which is made in special jigs from bulk standard size raw materials stocks. The standard gates ship in ironbark colour which blends closely to the natural colour of Australian brushwood and also gloss black. Other colours can be supplied to order.
![]() |
![]() |
![]() |
Front |
![]() |
Rear |
![]() |
|
![]() |
Corner Detail |
|
The Images Below Show the Fittings and Screws Supplied
with each Modular Pedestrian Gate. The Gate Post is Shown as galvanised finish for illustrative purposes in this image sequence, but normally would be powdercoated. Gate Posts are usually obtained locally by clients due to shipping aspects/ efficiencies. Powdercoated or galvanised finish gate posts with caps can be supplied by Ausbrush if required in 2500mm lengths and either 65mmx65mm or 75mmx75mm or 100mmx100mm steel sections. The post shown in these images is 65mmx65mm in section.
|
|
![]() |
Universal Hinges are Supplied - suitable for either Left or Right hung gates. |
![]() |
![]() |
| Cranked Brass Handle, Pad lockable 'D' Latch with 'D' Latch handle and Striker. | |
![]()
'D' Latch with 'D' Latch handle and Striker. In image at right, 'D' Latch handle is shown with arrow as it appears on the front side of gate. |
![]() |
![]() |
Brass
Brass Handle, and Striker for 'D' Latch |
![]() |
|
![]() |
|
![]() |
Front Side of Gate. Usually the gate posts are powdercoated also, but shown here as galvanised for illustrative purposes. |
| Rear Side of Gate. Showing horizontal cross braces. Gates wider than 900mm also have a diagonal cross braces. |
![]() |
![]() |
|
Traditional Brush Gates
Installation See our DVD for an easy guide to methods of traditional brushwood gate installation. See also our streaming video installation details below.
Traditional brush gates are made from hand thatched brush over a steel pipe frame and with brush frame rolls. They are very heavy and time consuming/expensive to make and fit.
For situations demanding an alternative brushwood gate size, framing or finishing method, we would be happy to work through your design with you and endeavour to supply your requirements.
![]() |
|
||
|
|
|
Copyright: Ausbrush Panels Ptd Ltd, Last Updated,
8th November, 2008
back to top